• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Fix a Loose Door Hinge

Repairing a broken door hinge can be a manageable task for the majority of homeowners. But, if the screw holes are damaged and aren't able to hold screws, you might need to put in dowels and wood glue before you can install the hinge.

Brush away any surface rust. This will help to keep the dowels in place and give them a solid base for them to grip onto.

Take the Hinges off

Most hinges on doors can be removed, which makes it easier to move the door from one side to another or to remove the entire door off the frame should it be needed. Anyone with a little patience can remove the hinges, but you need to know what to do.

If the hinges have been painted, you'll need to get rid of the paint prior to attempting to remove the pins. If you do not, the paint may peel off and scratch the door when you attempt to lift it. To break the seal of the paint put the hinges in a stainless steel pan and fill the pan with water until the hinges are fully submerged. Let the hinges sit in the pan for about 30 minutes. The heat from the water will soften the paint and make it easier to get rid of the pins.

After the pins have been loosened, remove the hinges and frame from the door. It is possible to use a standard screwdriver, but it is recommended to use a magnetic screwdriver for this task. This type of screwdriver has been specifically designed to take out metal screws and help you get the job accomplished much faster.

It is a good idea to spray lubricant onto the hinges prior to attempting to remove them. A simple lubricant can help the process to go more quickly and make it easier to remove the pins and screws. This type of lubricant can be found in most hardware stores and home improvement shops.

The number of hinges needed will also vary depending on the kind of door you have and the way it's set up. Heavier doors and solid-core Bi-Fold Doors Hinges will need more hinges, while hollow-core doors that weigh less might only require two or three.

It is also important to be aware of the various kinds of hinges to determine which ones will work best in your situation. The hinges on the exterior are designed to withstand the weight of a door, whereas interior hinges must be able support lighter loads.

Reattaching the Hinges

Over time the upvc hinges on doors can loosen and begin to sag or hang crookedly. This can be a problem, but it's usually easy to repair. In most cases, a simple retightening of the screw will resolve the problem. If the screw holes have been stripped out, it may be difficult to do. A wood dowel can be used to tighten these holes again.

Begin by drilling the hole using a drill close to the new screw size (normally 3/8"). Then use wood glue and a dowel made of wood to fill the hole. The dowel should be cut to a length exactly the same as the screw to ensure a snug fit. Reinstall the screw and tighten it to the desired degree of tightness. If the door does not stop bind up, you can insert another dowel into the gap. Repeat the process. Be sure to shut the door slowly to examine the clearances around the perimeter after each adjustment.

Another option is to utilize the wood plug instead of dowel. This will work as well however it may take some time to set up. Simply whittle a chunk of wood that is the right size for a snug fit, then press it into the hole. If you don't have a woodworking instrument or toothpicks, you can make use of toothpicks or matchsticks made of wood.

Use a countersink to make the hole smaller for the head of screw after you have reinstalled it. This will prevent the screw from rubbing against the edges of the doors as they are closed and opened. This will aid in tightening the screw after installing the hinge.

Once you've reinstalled your hinge, be sure to grease it using a dry lubricant to help keep it from getting stuck in the future. You can apply products such as PB Blaster and Liquid Wrench. You should apply a light coat and wait for around 15 minutes to fully get into the barrel of the hinge.

Refinishing the Hinges

If you're not yet ready to replace hinges on upvc window hinges, you could try a few fixes. Verify that the screws that attach the hinge plate to the door frame and the frame are tight. If they are loose, tighten them by using a drill or screwdriver. Be careful not to tighten your screws so tight that they begin to create gaps at the trim joints, or even worse cause threads to be stripped.

If the issue is that the hinge plates are separating, you can reattach the plates by applying wood glue on the back of them and inserting wooden dowels or toothpicks into the holes. The toothpicks and dowels provide a solid base for the screws, which will stop the plates from moving as you insert them. Allow the glue to dry before attaching the hinge.

The screws may also be smashed or gone. It is possible to fix this issue by replacing the screws with larger ones. Be sure to use a drill bit that matches the size of the screw hole in order to avoid drilling into other parts of the jamb or hinge.

Close the door after you have reattached your hinge and check the gap between the frame and the door. The gap should be about the thickness of a penny all around or less if the old door was hung incorrectly. This shouldn't be a problem as long as the hinges are properly installed.

If the hinges seem loose, you could add a thicker hinge between the hinge plate surface and the mounting surface. This will allow the hinges more room. You can also take off the hinge pin and pound it down with a powerful hammer to tighten it, or install an entirely new hinge. You can also lubricate the hinges using mineral or jojoba oil to reduce friction hinges for timber windows and help them hold their place. Lubricating your hinges periodically can stop them from becoming stiff and squeaky, and can also prolong their life.

Cleaning the Hinges

The continuous movement of hinges creates friction, which draws dust particles. These particles can become stuck and build up in the moving parts of door hinges if they are not cleaned and lubricated regularly. The hinge will become stiff and creaky, and its appearance could rapidly diminish. Regular cleaning, lubrication and inspection can preserve the quality of hinge on a door and ensure its proper function.

Check the hinges to see how much rust has accumulated on their surface. If the corrosion has reached the point of destroying the surface of the hinge barrel or screw holes, you will need to replace the hinges. If you can save the hinges, clean any loose rust with a wire brush and steel wool. Apply a commercial rust-removing product or a homemade solution such as lemon juice on the hinge. Let the rust removal solution sit on the hinge for several minutes to penetrate and dissolve any remaining corrosion.

The tightening of screws can restore hinge functionality If you don't wish to spend time or money on replacing hinges. It might be necessary to attach dowel or shim made of wood to the hinge in the event that the screws have been stripped. Dowels made of wood are round pieces of wood that are in the form of rods, which are available in different lengths and diameters. You can find them at home improvement centers, woodworking supply and craft shops, or on the internet.

A shim can be made of a piece of metal or plastic, depending on the kind of hinge you have. To make a dowel, cut a piece of wooden dowel or another sturdy material to the size you want. You can then dip the dowel into carpenter's glue before inserting it into the hole that you have stripped, allowing the glue to hold the dowel in place.

Before you begin cleaning the hinges, place down a towel or a paper towel to shield flooring and other surfaces from accidental spills and drips. After the area is secured then clean the hinges using a soft cloth or sponge coated with a mild cleaner or vinegar to remove built-up dirt, grime and tarnish. A small or toothbrush can be used to reach hard-to-reach areas in crevices and difficult areas.