• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat multipla key 500 Key Fob Won't Work

A fiat 500 spare key cost 500 key fob makes it easy to open doors and start your car. There are many reasons the key fob might stop working. These include a dead battery or damage to the receiver module, problems, and interference.

This listing is for a new key for fiat 500 replacement fiat 500 key fob programming Flip Key Remote - similar to the Ilco brand that must be professionally programmed by a local automotive locksmith (click here for Locksmith Search). Includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason that your 500 key fob will not function is a dead battery. Modern key fobs have a very limited operating range, and must be within a few feet of the vehicle in order to function. If you are not within your car and push the keyfob button it won't respond and display the message "Key Fob Not Detected".

If this happens, replace the coin cell battery (Part number CR2032) with a brand new one from a reputable brand like Panasonic, Duracell, or Energizer. You can typically find them at your local hardware store, or online.

After you've replaced the battery in the coin cell, you can test it by standing in front of your fiat key fob 500 and pressing the buttons. The car should blink its parking lights and the key fob should work the lock and unlock buttons.

If the fob's key doesn't work after replacing the battery, it could be damaged by water, which prevents it from connecting to the receiver module in your car. Water damage can happen in many ways, such as simply splashing or submerging the key fob into saltwater at the beach. If you suspect that your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If that doesn't work your fob will probably need to be reset by a professional locksmith or dealer.

Water Damage

Water damage can occur if you immerse the fob into the ocean or wash it in a washer. Saltwater poses a particular risk to the fob's circuit board and can cause it to short out and eventually end up dying. In the event that you let your fob get wet, it's not an ideal idea however, if you drop it in an empty cup of water, or don't remember to remove it from your pocket before you run the washing machine do not give up hope.

Remove the battery first. Clean the electronic chip using isopropyl alcohol or another similar product and then dry it completely before replacing the battery. Next check the fob to see if it works. If the key does not function, it may have to be reset. This is usually handled by a dealer or professional auto locksmith.

If your key is older and is not programmed for your car, you will need to replace it completely. This is an easy process that can be carried out by a professional automotive locksmith. The locksmith will need the key cut to match the car's ignition. The locksmith will also need to reprogram the fob into the car's system. This is a low-cost and quick procedure that can be completed in the same day.

Receiver Module Issues

One of the most common reasons why your 500 key fob could stop working is that it's simply out of range. The remote usually has an operating range of 30 feet or less and if it's far from your car, it will not respond to your commands. It is possible to solve this issue by moving the remote closer to your car until it responds.

If your fob isn't working after you replace the battery inside the coin, which is also known as a "button", "watch" or "button" it may be due to a malfunction on the internal circuit board. Reprogramming the fob is usually the solution to this problem. You can find directions on how to do this on the majority of automobiles by searching YouTube or looking through the owner's manual.

It is possible to replace the metal clips that hold the coin batteries in the correct position. If they loose tension, it can prevent your coin battery from being properly seated, causing your remote to malfunction.

In rare instances, the fob may become desync'd with your vehicle due to software issues or hardware issues. This issue can be fixed by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain instances they might need to install the software again in your body control module, as well.

Interference

Interference can also cause the key fob to be unable to receive or transmit an signal. This may happen if the keyfob is located in close proximity to a radio transmitter like a cellphone or radar detector. The key fob could not work due to a bad connection to the buttons water damage or damage to the internal chips.

If the key fob been unable to function for a while out of the blue or even after trying every option at home to fix it e.g. battery replacement, reprogramming and using the spare key fob, you might have a damaged receiver module on your 500. The receiver module is located under the dash, and it picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands, which are then read by the vehicle.

Luckily, there is an easy method to reset all of the onboard systems in your 500, including the key fob. Disconnect the battery for 15 minutes, removing first the negative cable and then the positive cable. Then, reconnect the battery. This will eliminate any remaining electricity and restart the car's computers. This can help you get your key fob working again. If the issue continues, you should seek out an expert technician. They can determine the root of your issue.